Buyer’s guide Seven checks

How to choose an industrial blower.

To choose an industrial blower, start from the pressure or vacuum the process needs, then check the flow, the technology, the air quality and dust, how the demand varies, the noise and site, and the maintenance and spares.

The seven checks at a glance

Seven questions before you buy.

Ask every industrial blower supplier the same seven questions, in writing, and compare the answers side by side.

CheckThe question to ask
1. Pressure or vacuumWhat pressure or vacuum does the process need, and is it differential or absolute?
2. FlowHow many m³/h, and at which pressure?
3. TechnologySide channel, rotary lobe or claw: which suits the duty?
4. Air qualityCan the air carry oil, and what dust or moisture comes in?
5. Variable demandHow does the blower follow the load, and what does it cost to run?
6. Noise and siteWhat is the sound level, and where does the blower stand?
7. Maintenance and partsWhat is the service interval, and who holds the spares in Portugal?
Check 1

The pressure or vacuum the process needs.

Start from the pressure or vacuum the process needs at the blower, in mbar, and ask whether a datasheet gives it as differential or absolute.

The background of US patent 11,815,105 (2023) says regenerative blowers, also called side channel blowers, move gas at pressures or vacuums lower than typical compressors and higher than centrifugal fans.

Elmo Rietschle says the same side channel machine can serve pressure or vacuum, depending on configuration and connection direction.

A process that needs more pressure than a blower gives is a job for a compressor: read how to choose a screw air compressor.

What the sources say
Side channel
Up to 1,000 mbar differential pressure in the Elmo Rietschle Product Guide (1,100 mbar on its website)
G-BH1
Up to 780 mbar differential pressure
G-BH100
Up to 100 mbar differential pressure
Positive displacement
1 to 14 psig for aeration blowers in the 2010 US EPA report, taking the range from WEF
Claw compressor
Oil-free, for continuous operation up to 2.2 bar overpressure, says Elmo Rietschle
Check 2

The flow, and the pressure it is stated at.

Ask for the flow in m³/h together with the pressure or vacuum it is stated at, and check that it is the same for every supplier.

Elmo Rietschle says side channel blowers excel at high flow rates and moderate vacuum, and that its G-Series typically reaches volume flows up to 3,000 m³/h, depending on model and configuration. The model pages give each series its own range.

The 2010 EPA report says a positive displacement blower gives a fixed volume of air for every shaft revolution, so its flow follows its speed. Ask what happens to the flow and the power when the pressure changes.

What the sources say
G-BH1
From 50 to 2,450 m³/h
G-BH2
Up to 850 m³/h
G-BH7
From 50 to 230 m³/h
G-BH100
From 21 to 35 m³/h
G-Series
Typically up to 3,000 m³/h, depending on model and configuration
Positive displacement
5 to 50,000 scfm for aeration blowers in the 2010 US EPA report
Check 3

The technology that fits the duty.

Side channel, rotary lobe and claw machines work in different ways and suit different duties, so compare them side by side before you compare prices.

Elmo Rietschle explains that in a side channel blower the impeller sits on the motor shaft and accelerates the gas inside the side channel by centrifugal force, so the compression is contact-free. Two- and three-stage models compress the gas across several stages for higher pressure ratios.

The US patent calls regenerative blowers comparatively simple, medium speed machines, unlike positive displacement compressors with their complex assembly and high parts count.

In the EPA table the most common positive displacement blower has two counter-rotating shafts with 2- or 3-lobed impellers. Elmo Rietschle compares its claw technology with the traditional rotary lobe design, which has no internal compression.

How each one works
Side channel
Contact-free flow compression, with the impeller on the motor shaft
Rotary lobe
Two counter-rotating shafts with 2- or 3-lobed impellers, in the EPA table
Claw
Contact-free, oil-free claw compression, says Elmo Rietschle
Check 4

The air quality: oil and dust.

Say whether the air may carry oil, and what dust, fluff or moisture the blower will draw in.

Elmo Rietschle describes its side channel blowers as dry running, and says that for long-term performance clean, dry gases are preferred and the inlet conditions, with filters and particle protection, should be properly designed.

It says the G-BH2 series is resistant to dust and fluff. The 2010 EPA report adds that air intakes are typically equipped with filters to protect blowers and diffusers from airborne particulates.

Elmo Rietschle also offers ATEX-certified G-Series blowers and ATEX-compliant claw compressors on request. If the site is a classified area, ask for the exact model and its certificate.

What the sources say
Side channel
Dry running, with contact-free compression
Inlet
Filters and particle protection, properly designed
G-BH2
Resistant to dust and fluff
Claw compressor
Oil-free; ATEX-compliant versions on request
G-Series
Also available with ATEX certification
Check 5

Variable demand and the cost of running.

Ask how the blower follows a changing load, and size it for the air the process really needs.

Elmo Rietschle says frequency converters are used to adapt the speed and performance of its side channel blowers to changing load, especially when suction demand or differential pressure fluctuates, and that the G-BH2 can run on a frequency converter up to 87 Hz.

The 2010 EPA report lists a simple control scheme for constant flow among the advantages of positive displacement blowers, and difficulty running at variable flow rates without a VFD among their disadvantages.

In wastewater aeration the same report says energy savings come from designing and operating the aeration to match, as closely as possible, the actual oxygen demand of the process. The wastewater treatment page has the detail.

What the sources say
Side channel
Frequency converters adapt speed and performance to changing load
G-BH2
Frequency converter operation up to 87 Hz
G-Series motors
Voltage range for 50, 60, 87 and 100 Hz
Positive displacement
Simple control for constant flow; difficult at variable flow without a VFD
Check 6

Noise, size and site.

Ask for the sound level in dB(A) of the exact model, with and without an enclosure, and say where the blower will stand.

The 2010 EPA report says positive displacement blowers can be noisy, and that enclosures are commonly used for noise control. The sources we use give no sound levels for blowers, so ask for them in writing.

For the site, Elmo Rietschle gives its G-Series motors protection class IP 55 or higher (IP56 or IP65) and insulation class F. If space is tight, it points to the G-BH100 as a small, adjustable-flow unit for a very compact design and small flow range.

What the sources say
Protection
IP 55 or higher (IP56 or IP65) on the G-Series motors
Insulation
Class F
Approvals
UL 507 and CSA 22.2 No. 113
G-BH100
Approx. 125 mm high and wide, 60 mm deep
Positive displacement
Can be noisy; enclosures commonly used
Check 7

Maintenance and who holds the parts.

Ask for the service interval of the exact model in hours, what the service involves, and who holds the spares in Portugal.

Elmo Rietschle gives up to 20,000 hours between services for its G-Series side channel blowers, up to 40,000 hours of runtime with virtually no maintenance in its overview brochure, and 40,000 hours maintenance free on the G-BH2 page. These are the manufacturer’s own figures, and the manual of the installed model sets the plan.

The 2010 EPA report says positive displacement blowers need more maintenance than the other types in its table.

Elmo Rietschle keeps datasheets, installation manuals and spare parts lists on its Technical Resources Finder, filtered by product, technology or document type.

How Ultra Controlo supports it
UltraCare, 24/7
Preventive and corrective maintenance, original spare parts and emergency support, 24 hours a day, 7 days a week
Our own technicians
Diagnosis, repair and maintenance on site by our own certified, factory-trained team, with scheduled maintenance plans for each installation
By technology at a glance

Four blower types, what each one suits.

A summary of what the sources say. The brand page lists the series we supply in Portugal: Elmo Rietschle.

TechnologyWhat it suitsWhat to checkIn our range in Portugal
Side channel (regenerative)High flow with a continuous, low-pulsation airflow, for pressure or for low to medium vacuum, says Elmo Rietschle.Dry running and contact-free; clean, dry gas is preferred, with inlet filters and particle protection.Elmo Rietschle G-BH1, G-BH2, G-BH7 and G-BH100.
Rotary lobe (positive displacement)A fixed volume of air for every shaft revolution over a wide range of discharge pressures, says the 2010 EPA report.Hard to run at variable flow without a VFD; can be noisy; needs more maintenance than the other types in the EPA table.Send us the duty, and our industrial team replies.
ClawOil-free compression for continuous operation up to 2.2 bar overpressure, says Elmo Rietschle.Elmo Rietschle compares claw technology with the traditional rotary lobe design, which has no internal compression; ATEX versions on request.Elmo Rietschle claw compressors, such as the C-KLR.
Centrifugal (turbo)Multi-stage, integrally geared and gearless high-speed types, which the 2010 EPA report compares for aeration.The EPA says efficiency at turndown differs from one type to another; see the wastewater treatment page.Send us the duty, and our industrial team replies.
Three common jobs

Three jobs, three duty points.

Aeration

The 2010 EPA report calls aeration blowers essentially low pressure, high volume air compressors. The wastewater treatment and aquaculture pages say what the sources give for air and oxygen.

Pneumatic conveying

Jenike & Johanson (2025) say a vacuum set-up offers excellent dust control and suits shorter distances, while positive pressure suits longer distances and higher capacities. Elmo Rietschle lists pneumatic conveying of granules, powders and light bulk materials among side channel uses.

Vacuum lifting, packaging and dust removal

The US patent background lists vacuum lifting, vacuum packaging, printing presses, dryers and dust removal among the uses of side channel blowers. For deeper vacuum, read how to choose an industrial vacuum pump.

Before you order

What to ask any supplier.

The duty point, in writing

Ask for the pressure or vacuum in mbar, the flow in m³/h at that pressure, and the power the blower draws.

The air, written down

Send the dust, the moisture and the temperature the blower will see, and say whether the air may carry oil.

The control

Ask how the blower follows a changing load, and whether the model runs on a frequency converter.

The sound level

Ask for the sound level in dB(A) of the exact model, with and without an enclosure.

Service and the manual

Ask for the service interval in hours, and for the datasheet and installation manual of the exact model before you order.

Parts and service

Ask who services the blower, and which spare parts are held in Portugal.

How Ultra Controlo answers

A partner brand, one team in Portugal.

Ultra Controlo distributes and services Elmo Rietschle in Portugal as a partner brand. The blowers on our brand page are the G-Series side channel blowers, in the G-BH1, G-BH2, G-BH7 and G-BH100 series, and the oil-free claw compressors. The equipment is made by Elmo Rietschle.

Tell us the pressure or vacuum, the flow, the air and the site, or the machine you want to replace. For any other technology, send us the duty, and our industrial team replies.

Pumping a liquid rather than a gas? Read how to choose an industrial pump.

Frequently asked questions

Common questions about choosing a blower.

Questions buyers ask us about industrial blowers. More on the medical gas answers page.

How do I choose an industrial blower?

To choose an industrial blower, start from the pressure or vacuum the process needs, then check the flow, the technology, the air quality and dust, how the demand varies, the noise and site, and the maintenance and spares.

Send the supplier the pressure or vacuum, the flow, the air and the site.

Side channel or rotary lobe blower: which one?

It depends on the duty. The 2010 US EPA report says rotary lobe (positive displacement) machines give a fixed volume of air per shaft revolution over a wide range of discharge pressures, while Elmo Rietschle says side channel blowers excel at high flow rates and moderate vacuum.

Is a side channel blower the same as a regenerative blower?

Yes. Elmo Rietschle notes that side channel blowers are also referred to as regenerative blowers, and that the terminology varies by industry.

Can a side channel blower make vacuum as well as pressure?

Yes. Elmo Rietschle says side channel blowers are commonly used for both pressure and vacuum applications, depending on configuration and connection direction.

Which blower do I need for wastewater aeration?

It depends on the flow, the pressure and how much the air demand varies. The 2010 US EPA report describes aeration blowers as low pressure, high volume air compressors, commonly positive displacement or centrifugal, and compares four blower types for aeration; the wastewater treatment page sets them out.

Does Ultra Controlo service blowers in Portugal?

Yes. Ultra Controlo distributes and services Elmo Rietschle vacuum pumps and blowers, and its UltraCare programme covers Ultra Controlo equipment and partner brands.

Request a project assessment

Ready to discuss an industrial blower?

Send us the pressure or vacuum, the flow, the air quality and the site, or the machine you want to replace. Our industrial team replies with the model that fits.

ISO 9001:2015
ISO 14001
80+ countries
40 years