Buyer’s guide Eight checks

How to choose a screw air compressor.

To choose a screw air compressor, compare suppliers on eight points: air needs, working pressure, fixed or variable speed, control of several compressors, oil lubricated or oil-free air, efficiency data, heat recovery and maintenance.

ULTRASCREW screw compressor, front view of the dark grey enclosure
The eight checks at a glance

Eight questions before you buy.

Ask every screw compressor supplier the same eight questions, in writing, and compare the answers side by side.

CheckWhat to ask the supplier
1. Air needsWhich air quality, quantity and pressure do the end uses need?
2. Working pressureWhat is the lowest efficient pressure, and what capacity does the compressor give at it?
3. Fixed speed, variable speed or two-stageHow does the compressor follow demand at part load?
4. Several compressorsHow are they controlled together, and does one trim?
5. Oil lubricated or oil-freeDoes the end use need lubricant-free air, and how is it delivered?
6. Efficiency dataIs it stated to the same standard and at the same conditions?
7. Heat recoveryCan the compressor heat be recovered, and for what?
8. MaintenanceWhat does the manufacturer’s schedule require?
Check 1

Your air needs.

Start from what the end uses need: the air quality, the quantity and the pressure.

Compressed Air Challenge Fact Sheet #1 (May 2026) lists four air quality levels, plant air, instrument air, process air and breathing air, and says industrial applications typically use one of the first three.

Capacity is found from the sum of the average air consumption of each tool and process, not the sum of their maximum requirements, and high short-term demands should be met by air stored in an air receiver.

How ULTRASCREW does it

In ULTRAAR ME and ULTRAOX ST the compressor is sized by altitude band, up to 3,000 m.

For ULTRASCREW DS VSD, the Ultra Controlo engineering team sizes the configuration and sends a quote.

Check 2

The working pressure.

Specify the lowest efficient operating pressure, then read the capacity at that pressure.

Fact Sheet #4 says equipment should be specified and operated at the lowest efficient operating pressure, and to check with the compressor manufacturer for performance specifications at different discharge pressures. Fact Sheet #1 gives a rule of thumb: every 2 psi increase in operating pressure requires an additional 1% in operating energy costs.

Why does pressure drop cost energy?

How ULTRASCREW does it

In the ULTRAAR ME datasheet (2026), the fixed speed ULTRASCREW models are listed at 10 bar and, from ULTRASCREW 7 FSD to ULTRASCREW 110 FSD, at 13 bar, with a lower capacity at 13 bar: ULTRASCREW 37 FSD lists 322 Nm³/h at 10 bar and 265 Nm³/h at 13 bar.

The variable speed version operates at constant output pressure over a range of 5 to 14 bar, with a smooth start.

Check 3

Fixed speed, variable speed or two-stage.

Few air systems operate at full load all the time, so ask how the compressor follows demand.

Fact Sheet #6 says part-load performance is critical and is primarily influenced by compressor type and control strategy. In most cases, an unloaded rotary screw compressor consumes 15 to 35% of full-load horsepower while delivering no useful work, and variable frequency drives are widely accepted in compressor applications.

The US Department of Energy sourcebook (2016) says two-stage rotary screw compressors are generally more efficient than single-stage units.

How ULTRASCREW does it

ULTRASCREW FSD runs at fixed speed with a star delta starter, and ULTRASCREW VSD uses direct drive and variable speed control.

ULTRASCREW DS VSD is for industrial operations where compressed air demand fluctuates: two-stage screw compression with a variable speed drive that follows air demand.

Check 4

Several compressors on one header.

Ask how the compressors are coordinated, and whether one unit trims while the others run at full load.

Fact Sheet #6 says all units that are on should run at full load, except one unit for trimming. It describes single master (sequencing) controls, where all operating decisions are made and directed from the master unit, and multi-master (network) controls, where the controllers are networked, share all operating information and status, and one is designated the leader.

How ULTRASCREW does it

On ULTRASCREW DS VSD, several compressors can run as a group without an external master controller. The control is an LED display with integrated driver and controller, Modbus TCP and dual PID control of pressure and temperature at the same time.

Check 5

Oil lubricated or oil-free.

Ask whether the end use needs lubricant-free air, and how the supplier delivers it.

Fact Sheet #1 says one of the main factors in determining air quality is whether or not lubricant-free air is required. Lubricant-free rotary screw compressors usually have higher first costs, lower efficiency and higher maintenance costs than lubricant-injected compressors, while the additional separation and filtration of a lubricant-injected compressor causes some reduction in efficiency, especially if the system is not properly maintained.

ISO 8573-1 defines purity classes for compressed air with respect to particles, water and oil.

Oil-injected compressor

How ULTRASCREW does it

ULTRASCREW is an oil lubricated rotary screw compressor. For oil-free compression, see ULTRACECO, in ULTRACECO and ULTRASCREW compressors and airends.

Check 6

Efficiency, on the same basis.

Compare data sheets tested to the same standard and at the same conditions.

Fact Sheet #8 names ISO 1217, Displacement Compressors Acceptance Tests, as the recognized performance standard for displacement compressors, including rotary screw compressors. It says standard conditions should be 1 bar, 20 °C and dry, that the bhp rating, not the motor nameplate rating, should be used, and that a rating in total kW input per acfm includes motor efficiency and all package accessories and losses.

Part-load efficiency matters too, because most systems operate at part load much of the time.

Free air delivery

How ULTRASCREW does it

The ULTRASCREW datasheet states that air flow is measured in accordance with ISO 1217:2009, Annex C, and that its values refer to 1 bar absolute, 0% relative humidity and 20 °C inlet air temperature.

Check 7

Heat recovery.

Ask whether the compressor heat can be recovered, and what it can be used for.

Fact Sheet #10 says as much as 80 to 93% of the electrical energy consumed by an industrial air compressor is converted into heat, and that with a properly designed heat recovery system, 50 to 90% of this thermal energy can often be captured and reused for heating air or water. Typical uses include supplemental space heating, industrial process heating, water heating, makeup air heating and boiler makeup water preheating.

Compressor heat recovery

How ULTRASCREW does it

ULTRASCREW DS VSD has an optional oil/water exchanger that recovers compressor heat as hot water for facility use, or as heated air for space heating.

Check 8

Maintenance and service.

Ask for the manufacturer’s maintenance schedule, and follow it.

Fact Sheet #5 says equipment should be maintained in accordance with manufacturers’ specifications and that their schedules should be followed strictly. For a lubricant-injected rotary screw compressor, it says to inspect the lubricant level daily and to change the air/lubricant separator per manufacturer specifications or when pressure drop exceeds 10 psid, whichever is less.

What maintenance does a medical air plant need?

How ULTRASCREW does it

The fixed speed ULTRASCREW is presented with a compact footprint with easy servicing, and the variable speed version with air/oil cooling with cyclonic separator and a pressure relief valve.

Frequently asked questions

Common questions about choosing a screw compressor.

Questions buyers ask when choosing a screw air compressor.

What should I compare when buying a screw air compressor?

To choose a screw air compressor, compare suppliers on eight points: air needs, working pressure, fixed or variable speed, control of several compressors, oil lubricated or oil-free air, efficiency data, heat recovery and maintenance.

How is a screw air compressor sized?

Compressed Air Challenge Fact Sheet #1 (May 2026) says required capacity is found by summing the requirements of the tools and process operations at the site, taking load factors into account. The total is not the sum of the maximum requirements for each tool and process, but the sum of the average air consumption of each.

Should I choose a fixed speed or a variable speed compressor?

Compressed Air Challenge Fact Sheet #6 says part-load performance is critical and is primarily influenced by compressor type and control strategy. ULTRASCREW is offered in fixed speed (FSD) and variable speed (VSD) versions: FSD runs at fixed speed with a star delta starter, and VSD uses direct drive and variable speed control.

Does a screw compressor give oil-free air?

Not by itself. Compressed Air Challenge Fact Sheet #1 says lubricant-free air can be produced with lubricant-free compressors, or with lubricant-injected compressors that have additional separation and filtration equipment. ULTRASCREW is an oil lubricated rotary screw compressor, and for oil-free compression Ultra Controlo refers to ULTRACECO.

How are several compressors controlled together?

Compressed Air Challenge Fact Sheet #6 describes single master (sequencing) controls, where all operating decisions are made from the master unit, and multi-master (network) controls, where networked controllers share information and one is designated the leader. On ULTRASCREW DS VSD, several compressors can run as a group without an external master controller.

Can compressor heat be recovered?

Yes. Compressed Air Challenge Fact Sheet #10 says as much as 80 to 93% of the electrical energy consumed by an industrial air compressor is converted into heat, and that with a properly designed heat recovery system 50 to 90% of it can often be captured and reused for heating air or water. On ULTRASCREW DS VSD, an oil/water exchanger is available as an option.

Who supplies ULTRASCREW compressors?

ULTRASCREW compressors are supplied by Ultra Controlo. Ultra Controlo also distributes and services Gardner Denver compressors, according to its Industrial 2026 catalogue.

Request a project assessment

Ready to discuss compressed air for your plant?

Tell us about your site, the air demand and the working pressure. Our engineering team sizes the configuration and sends a quote.

ISO 9001:2015
ISO 14001
80+ countries
40 years