Buyer’s guide Eight checks

How to choose an industrial vacuum pump.

To choose an industrial vacuum pump, start from the vacuum level the process needs, then check the flow, the gas and vapours the pump will draw in, whether it runs dry or oil-lubricated, the temperature, the noise and site, the maintenance and spares, and the energy it uses.

The eight checks at a glance

Eight questions before you buy.

Ask every industrial vacuum pump supplier the same eight questions, in writing, and compare the answers side by side.

CheckWhat to ask the supplier
1. Vacuum levelWhat absolute pressure, in mbar, does the process need, and at what flow?
2. FlowWhat flow in m³/h does the pump give at that working vacuum?
3. Gas and vapoursDoes the gas carry moisture, steam, solvents or dust?
4. Dry or lubricatedDoes the process allow oil in the pump, and in the exhaust?
5. TemperatureHow hot are the gas and the pump, and how is the pump cooled?
6. Noise and siteWhat is the noise level, and where does the pump sit?
7. Maintenance and partsWhat upkeep does it need, and who holds the spares in Portugal?
8. EnergyHow does the pump follow demand, and what does it cost to run?
Check 1

The vacuum level the process needs.

Start from the absolute pressure the process needs, in mbar, and ask for the vacuum the pump gives at your flow, not only its ultimate vacuum.

The US Department of Energy sourcebook (2016) defines vacuum pumps as compressors that operate with an intake pressure below atmospheric pressure and discharge to atmospheric pressure or slightly higher.

The technology sets how deep the vacuum can go. Elmo Rietschle says the oil seal of its oil-lubricated vane pumps is what allows deeper vacuum levels.

Absolute and differential values are not the same thing, so ask which one a datasheet gives.

What the manufacturers say
Liquid ring
Suction pressure down to 33 mbar abs., say Elmo Rietschle and Circutec
Oil-lubricated vane
Ultimate vacuum of 0.5 mbar (abs.) on the V-VCS
Dry running vane
Operating range up to 200 mbar (abs.) on the V-VTR
Claw
30 mbar (abs) on the C-VLU
Screw
End vacuum of 0.08 mbar (abs) on the S-VSI
Side channel
Up to 1,000 mbar differential pressure in the Elmo Rietschle Product Guide (1,100 mbar on its website)
Diaphragm
Thomas gas diaphragm pumps: vacuum to −990 mbar
Check 2

The flow, and the vacuum it is stated at.

Ask for the flow in m³/h together with the vacuum it is stated at, and check that it is the same for every supplier.

The ranges differ a great deal from one technology to another, from the litres per minute of a diaphragm pump to the thousands of cubic metres per hour of a central screw plant.

Elmo Rietschle says side channel blowers are particularly suitable when a continuous, low-pulsation airflow is required and the vacuum level lies in the low to medium range.

What the manufacturers say
Diaphragm
The Thomas 8311 gives up to 43 l/min at 230 V, 50 Hz
Dry running vane
From 3 m³/h (V-VTE) to 154 m³/h (V-VTR)
Liquid ring
L-BV5 from 90 to 590 m³/h
Claw
C-VLR 1000 up to 1140 m³/h
Screw
IDS up to 1030 m³/h; SVT up to 5,740 m³/h (SVT6000)
Side channel
Up to 3,000 m³/h
Check 3

The gas and vapours it will draw in.

Write down every gas, vapour and particle the pump will draw in, and choose the technology for the wettest condition.

For gas that carries moisture, Elmo Rietschle says its L-Series liquid ring vacuum pumps are designed for extreme wet processes, and offers the V-VCX oil-lubricated vane pump, with chemically resistant resin vanes and an adjustable gas ballast valve, for applications containing moisture.

Elmo Rietschle says alternative technologies, such as dry-running screw or rotary vane, can be suitable when the gas stream is dry and well-defined.

Circutec says its liquid ring pumps come in ATEX versions suited to explosive gases such as hydrogen. Elmo Rietschle says select rotary vane models are available for oxygen conveying, without naming them, so ask for the exact model.

For dust, Elmo Rietschle puts a micro-fine filter on the suction side of the V-VTN, and recommends properly designed inlet filters and particle protection for its side channel blowers.

What the manufacturers say
Liquid ring
For gas with moisture, steam or condensate
V-VCX
Oil-lubricated vane pump for high moisture
V-VCS XD
Versions for high water vapour loads and solvents
Screw
High water vapour tolerance
Claw
XD versions handle humid and wet processes
Check 4

Dry or oil-lubricated.

Decide whether the process can have oil inside the pump, and whether it can have any in the exhaust.

Elmo Rietschle says its oil-lubricated pumps use oil as lubricant, sealing agent and cooling medium, and that its dry running pumps are designed to operate without oil lubrication.

In its oil-lubricated vane pumps, Elmo Rietschle says a de-oiling chamber separates oil particles from the gas, and describes the discharged gas as virtually oil-free.

Elmo Rietschle says the oil-free design of its dry running vane pumps eliminates maintenance concerns related to oil, and that the C-VLU claw pump has no oil or filters to replace frequently.

Check each model, not each series: the screw page describes the S-VSI and the IDS as oil-free, while the SVT page describes oil-lubricated screw technology.

What the manufacturers say
Rotary vane
Oil-lubricated pumps such as the V-VCS use oil to seal and reach deeper vacuum; dry running pumps such as the V-VTN and V-VTR are designed to operate without oil lubrication
Food contact
Elmo Rietschle says its ECO-LUBE lubricant was developed to fulfil FDA 21 CFR 178.3570 (lubricants with incidental food contact) and USDA H-1
SVT
Oil-lubricated screw pumps with oil carry-over of 3 ppm or less
Diaphragm
Thomas says its diaphragm pumps are oil-less and can run dry, and suit pressure, vacuum or a combination of the two
Check 5

Temperature and cooling.

Ask how hot the gas and the pump run, and how the pump is cooled.

On a liquid ring pump, Elmo Rietschle says the vacuum is limited by the vapour pressure of the operating liquid: as the liquid warms, its vapour pressure rises and the achievable ultimate vacuum decreases. For stable vacuum levels it recommends cooling the operating liquid or using a circuit with a heat exchanger.

In its oil-lubricated pumps, Elmo Rietschle says the oil carries away the heat of compression.

Ask for the maximum gas temperature at the inlet, in the datasheet of the exact model.

What the manufacturers say
Liquid ring
Cool the operating liquid, or use a circuit with a heat exchanger
Oil-lubricated vane
The oil carries away the heat of compression
Dry running vane
Air-cooled
Claw
Cooling air is sucked in between the compression housing and a silencing cover before it leaves the pump
Screw
Cooling through a water-cooled outer chamber, with optional cooling gas for specific pump sizes
Check 6

Noise and the site.

Ask for the noise level in dB(A) and the conditions it is measured in, and decide where the pump will sit.

Elmo Rietschle lists a low sound level among the features of its claw pumps and a low noise level among those of its screw pumps, and its datasheet D281 lists a noise protection cover as standard on the V-VTN.

For central vacuum, Elmo Rietschle says a remote plant room keeps heat and noise out of the production hall.

What the manufacturers say
Claw
Air cooling and a low sound level
Screw
A low noise level
V-VTN
Air cooling, a fine mesh filter, a vacuum safety valve and a noise protection cover as standard
SVT
68 to 85 dB(A) by model in the SVT brochure; a remote plant room keeps the noise out of the hall
Check 7

Maintenance and spare parts.

Ask what upkeep the pump needs and who holds the spare parts in Portugal.

The Elmo Rietschle FAQ says maintenance typically includes changing oil where applicable, inspecting and replacing filters, checking and tightening connections and monitoring system performance, and that the recommended intervals are in the product manuals.

For its oil-lubricated rotary vane pumps, the V-Series brochure offers service kits, and the G-Series page gives up to 20,000 hours between services for side channel blowers.

Elmo Rietschle’s Technical Resources Finder gives access to datasheets, installation manuals and spare parts lists, filtered by product, technology or document type.

How Ultra Controlo supports it
UltraCare, 24/7
Preventive and corrective maintenance, original spare parts and emergency support, 24 hours a day, 7 days a week
Our own technicians
Diagnosis, repair and maintenance on site by our own certified, factory-trained team, with scheduled maintenance plans for each installation
Check 8

Energy and the cost of running.

Compare how the pump follows demand, and do not make vacuum with compressed air unless the use is very intermittent.

The Compressed Air Challenge Fact Sheet #2 (May 2026) says plants should apply a vacuum system instead of creating a vacuum using compressed air venturi methods that flow high pressure air past an orifice.

The 2016 US Department of Energy sourcebook says compressed-air vacuum generators are usually less economical to operate than central vacuum systems, and that a dedicated vacuum pump or a central vacuum system provides more suction force at a fraction of the cost of vacuum produced by compressed air. It adds that for very intermittent use compressed air can be a reasonable solution.

On the pump side, Elmo Rietschle says its SVT series holds precise setpoints with integrated variable-speed control and reduces energy waste, and that running at 60 mbar when a process needs 100 mbar can inflate power use by 30 to 40%. The page gives no baseline, so these are the manufacturer’s statements.

What the manufacturers say
SVT
Integrated variable-speed control, 100 to 250 mbar (abs), up to 8 pumps coordinated
V-VCS
IE3 motor as standard, IE4 option
Claw
Variable speed drives available
By technology at a glance

Seven pump types, what each one suits.

A summary of what the manufacturers say. The series we supply in Portugal for each technology are on the industrial vacuum pumps page.

TechnologyWhat it suitsWhat to check
Liquid ringGas with moisture, steam or condensate, says Elmo Rietschle.The vacuum is limited by the vapour pressure of the operating liquid, and the liquid has to be managed.
Rotary vane, oil-lubricatedDeeper vacuum levels: the oil is what seals the pump.Oil in the pump; a de-oiling chamber leaves the exhaust virtually oil-free.
Rotary vane, dry runningClean, dry, contamination-free operation, with no oil maintenance.Air-cooled; check the vacuum level, which is higher in absolute pressure than the lubricated pumps.
ClawContact-free, oil-free compression.No oil or filters to replace frequently on the C-VLU; XD versions for humid and wet processes.
ScrewContact-free compression with high vapour and liquid tolerance.Check the model: some are oil-free, the SVT is oil-lubricated.
Side channelHigh flow at a low to medium vacuum, with continuous, low-pulsation airflow.Dry running and contact-free; the vacuum level has to lie in the low to medium range.
DiaphragmSmall flows, in an oil-less pump that can run dry, says Thomas.Check the flow: the 8311 gives up to 43 l/min.
Before you order

What to ask any supplier.

The numbers, in writing

Ask for the vacuum in mbar, the flow in m³/h at that vacuum, and the power the pump draws.

The gas, written down

Send the gas, the vapours, the dust and the temperature the pump will see.

Dry or lubricated

Ask whether the exact model runs oil-free or oil-lubricated, and what the exhaust carries.

Noise and cooling

Ask for the sound level in dB(A) and for how the pump is cooled.

Parts and service

Ask who services the pump, and which spare parts are held in Portugal.

The datasheet

Ask for the datasheet and the installation manual of the exact model before you order.

How Ultra Controlo answers

Partner brands, one team in Portugal.

Ultra Controlo distributes and services industrial vacuum pumps in Portugal as partner brands: liquid ring, rotary vane, screw, claw and side channel pumps from Elmo Rietschle, liquid ring pumps and vacuum units from Speck Pumpen (Circutec), and diaphragm and piston vacuum pumps from Thomas. The equipment is made by each manufacturer.

The industrial vacuum pumps page lists, for each technology, the series we supply from each brand, and the brand pages say what each manufacturer states about them. Tell us the pump or the technology, the quantity and the site, or the machine you want to replace.

Looking for hospital vacuum? That is a separate line of Ultra Controlo: read how to choose a medical vacuum plant.

Pumping a liquid rather than a gas? Read how to choose an industrial pump.

Frequently asked questions

Common questions about choosing a vacuum pump.

Questions buyers ask us about industrial vacuum pumps. More on the medical gas answers page.

How do I choose an industrial vacuum pump?

To choose an industrial vacuum pump, start from the vacuum level the process needs, then check the flow, the gas and vapours the pump will draw in, whether it runs dry or oil-lubricated, the temperature, the noise and site, the maintenance and spares, and the energy it uses.

Send the supplier the vacuum, the flow, the gas and the site.

Which vacuum pump suits wet gas or condensate?

Elmo Rietschle designs its L-Series liquid ring vacuum pumps for extreme wet processes, and offers the V-VCX oil-lubricated vane pump, with chemically resistant resin vanes and an adjustable gas ballast, for applications containing moisture.

Is a dry running vacuum pump better than an oil-lubricated one?

It depends on the process. Elmo Rietschle says the oil seal of its oil-lubricated vane pumps is what allows deeper vacuum levels, and that the oil-free design of its dry running vane pumps eliminates maintenance concerns related to oil.

Can compressed air make the vacuum instead of a pump?

The 2016 US Department of Energy sourcebook says compressed-air vacuum generators are usually less economical to operate than central vacuum systems, although for very intermittent use compressed air can be a reasonable solution.

Is a side channel blower the same as a regenerative blower?

Yes. Elmo Rietschle notes that side channel blowers are also referred to as regenerative blowers, and that the terminology varies by industry.

Does Ultra Controlo make these vacuum pumps?

No. The Industrial 2026 catalogue lists them as partner brands that Ultra Controlo distributes and services; the equipment is made by each manufacturer.

Does Ultra Controlo service vacuum pumps in Portugal?

Yes. Ultra Controlo distributes and services Elmo Rietschle vacuum pumps and blowers, and its UltraCare programme covers Ultra Controlo equipment and partner brands.

Request a project assessment

Ready to discuss an industrial vacuum pump?

Send us the vacuum level, the flow, the gas and the site, or the machine you want to replace. Our industrial team replies with the model that fits.

ISO 9001:2015
ISO 14001
80+ countries
40 years