Buyer’s guide Eight checks

How to choose an industrial pump.

To choose an industrial pump, start from the liquid and its temperature, then check the flow and head, the NPSH and the risk of cavitation, any gas in the liquid, the pressure, the materials, the shaft seal or magnetic drive, and the maintenance and spare parts.

The eight checks at a glance

Eight questions before you buy.

Ask every industrial pump supplier the same eight questions, in writing, and compare the answers side by side.

CheckWhat to ask the supplier
1. Liquid and temperatureWhat is the liquid, how hot is it, how viscous, and does it carry solids?
2. Flow and headWhat flow and what head does the duty point need, and how often does it change?
3. NPSH and cavitationWhat NPSH does the pump need at that flow, and how much does the system provide?
4. Gas in the liquidCan the liquid carry gas or vapour, and must the pump prime itself?
5. High pressureIs the pressure high and the flow low, and what safeguards does the pump need?
6. MaterialsWhat are the wetted metals, plastics and elastomers, by code?
7. Seal and magnetic driveIs a shaft seal acceptable, or must the pump be sealless?
8. Maintenance and partsWhat wears, how often, and who holds the spares in Portugal?
Check 1

The liquid and its temperature.

Write down the liquid, its temperature range, its viscosity and the solids it carries, because they rule out whole technologies before the flow is considered.

The US Department of Energy sourcebook (2006) says that pump requirements are influenced greatly by fluid characteristics such as viscosity, density, particulate content and vapour pressure.

It adds that some fluids, such as cold lubricating oil, are so viscous that centrifugal pumps cannot move them effectively, so the range of viscosities over the operating temperatures is a key design factor.

Name the liquid exactly, give its temperature at start-up as well as in service, and say whether it is clean, cloudy or abrasive: the limits below depend on it.

What the manufacturers say
Centrifugal
Speck Pumpen (Circutec): clear liquids with no abrasive contamination or solid content
Side channel
Circutec: clear to lightly contaminated liquids similar to water; hot water up to 180 °C, heat transfer oils from −100 °C to 350 °C
Regenerative turbine
Circutec: clear or cloudy liquids with no abrasive contamination or solids, and a kinematic viscosity of up to 100 mm²/s
Plunger
Speck Triplex: the NP series is for clean water and other non-aggressive or non-abrasive media with a specific weight similar to water
Peristaltic
Thomas: only the tubing touches the liquid, and the pump tolerates particles and suits viscous or aggressive media
Check 2

The flow and the head at the duty point.

Ask for the flow and the head at the duty point, then choose the pump whose best efficiency point lies close to it, not the biggest pump on the list.

The US Department of Energy sourcebook says each centrifugal pump has a best efficiency point, where its efficiency is highest and its radial bearing loads are lowest, and that a pump whose best efficiency point is close to the normal operating range can bring significant operating cost savings.

It warns that engineers often overlook the cost of oversizing a pump, which means higher operating and maintenance costs, and that oversized pumps typically need more frequent maintenance. For a displacement pump the logic is different: its flow is directly proportional to its speed, and the system’s resistance sets the pressure.

The European Commission says that the clean water pumps covered by Regulation (EU) No 547/2012 used 179 TWh of electricity in 2020, 7.5% of EU27 electricity consumption. The sourcebook adds that for most facilities lifetime energy costs or maintenance costs, or both, dominate life-cycle costs.

What the manufacturers say
Vertical multistage
Up to 160 m³/h and 250 m on the IN-VB and IN-VC, says SPECK (Neunkirchen)
Process centrifugal
KN, KNG and KNV from 20.0 to 185.0 m³/h, says Speck Pumpen (Circutec)
Centrifugal, in general
Circutec: well suited to high flow rates at relatively low pressures
Regenerative turbine
Circutec: suited to high pressures at relatively low flow rates
Plunger
Speck Triplex NP series, from 1.2 l/min at 170 bar (NP10/1-170) to 134 l/min at 100 bar (NP30/140-100)
Check 3

The NPSH and the risk of cavitation.

Ask for the NPSH the pump requires at your flow, and check that your system provides more, with a margin.

The US Department of Energy sourcebook explains that a centrifugal pump must have a certain pressure at its inlet to avoid cavitation, called the net positive suction head (NPSH). NPSHA is what the system provides at the inlet and NPSHR is what the pump requires, usually shown on its performance curve.

As defined by the Hydraulic Institute, the sourcebook says, NPSHR is the point where the pump’s head falls by 3% because of cavitation, now called NPSH3. A common design rule is to keep NPSHA 25% above NPSHR at all expected flow rates, and an oversized pump running far from its design point can leave a dangerously small margin.

The sourcebook also warns that excessive cavitation affects efficiency and can damage the pump, and that trimming an impeller can raise NPSHR in some pumps, so ask for the NPSH at the diameter you will actually receive.

For a low suction head or a liquid close to its boiling point, Speck Pumpen (Circutec) says its side channel pumps with an NPSH inducer stage, an additional radial impeller, can be used with a low suction head and suit media at temperatures close to boiling point.

What the manufacturers say
Side channel
The ASK combi-pump adds an NPSH inducer stage, a radial impeller, says Circutec
Centrifugal
Circutec adjusts the pump to the operating point by changing the impeller diameter
Liquid diaphragm
Thomas says its resonating diaphragm reduces the effect of cavitation and air bubble formation
Check 4

Gas in the liquid, and priming.

Ask whether the liquid can carry gas or vapour and whether the pump has to prime itself, because that separates the technologies.

Speck Pumpen (Circutec) says its centrifugal pumps are normal-priming and not suitable for the delivery of gas shares, while it describes its side channel pumps and its displacement pumps as suitable for the delivery of gas shares and self-priming. It also lists its regenerative turbine pumps as suitable for the delivery of gas shares.

The US Department of Energy sourcebook lists a pump that must be self-priming among the situations in which displacement pumps are typically more appropriate. Thomas says its peristaltic pumps and its liquid diaphragm pumps are self-priming.

SPECK (Neunkirchen) describes its vertical multistage pumps as normal-priming high-pressure centrifugal pumps. If gas can enter the pump, say so in the enquiry: the answer changes the technology, not only the size.

What the manufacturers say
Centrifugal
Circutec: normal-priming, not suitable for the delivery of gas shares
Side channel
Circutec: suitable for the delivery of gas shares, and self-priming
Regenerative turbine
Circutec: suitable for the delivery of gas shares, and delivers pulsation-free
Displacement
Circutec roller vane and gear pumps: suitable for gas shares and self-priming, with no return flow of the medium when stopped
Peristaltic
Thomas: self-priming and able to run dry
Check 5

High pressure at low flow.

For high pressure at low flow, look at regenerative turbine, displacement and plunger pumps, and ask what safeguards the system needs with them.

The US Department of Energy sourcebook says displacement pumps are used in low-flow, high-head applications, and are typically more appropriate when the system requires high-pressure, low-flow performance. It adds that they typically need more system safeguards, such as relief valves, because a displacement pump can overpressurise the piping if the valves downstream are closed.

The sourcebook also notes that the pulsating flow of many displacement pumps can hasten the degradation of piping, valves and supports, and that these pumps are very susceptible to wear from abrasives in the liquid.

Speck Triplex lists unloaders and pressure relief valves matched to its pumps, and its NP series table names a recommended unloader for each model.

What the manufacturers say
Plunger
Speck Triplex: from 1.2 l/min (NP10/1-170) to 500 l/min (P80) and up to 1,200 bar (P55/18-1200)
Regenerative turbine
Circutec: particularly suitable for high pressures at relatively low flow rates, delivering pulsation-free
Roller vane and gear
Circutec: DS roller vane pumps for outlet pressures up to 14.0 bar (50 Hz), and ZY-MK and ZY-MM gear pumps for high-pressure applications
Side channel
Circutec: PN 40, with higher delivery pressures from multi-stage designs
Check 6

The materials the liquid touches.

Ask for the material of every part the liquid touches, and for the code of the exact model, not only the series.

The same series can come in different materials: Speck Pumpen (Circutec) lists its side channel pumps in bronze and spheroidal graphite cast iron, and its centrifugal pumps in grey cast iron, spheroidal graphite cast iron or stainless steel.

Speck Triplex says its pumps can normally be fitted with special seals, for example Viton, Teflon and FFKM, on request, and that it offers stainless steel pumps besides its standard range. In its type names, R means stainless steel AISI 303 or equivalent and RE means AISI 316 or equivalent.

Thomas says silicone tubing is commonly used on peristaltic pumps for non-aggressive media, and fluoroelastomer tubing for more chemically corrosive media. Its liquid diaphragm pumps use EPDM, FKM, PTFE or FFKM.

What the manufacturers say
Side channel
Circutec: bronze and spheroidal graphite cast iron
Centrifugal
Circutec: grey cast iron, spheroidal graphite cast iron or stainless steel
Vertical multistage
SPECK (Neunkirchen): all wetted parts in stainless steel
Plastic
SPECK (Neunkirchen): self-priming plastic centrifugal pumps for acids, alkalis and plating baths
Plunger
Speck Triplex: R is AISI 303 or equivalent, RE is AISI 316 or equivalent
Check 7

The shaft seal, or a magnetic drive.

Decide whether a shaft seal is acceptable or whether the pump must be sealless, and ask what each choice means for maintenance.

Speck Pumpen (Circutec) describes its magnetic coupling pumps as leakage-free, low-maintenance and safe in operation. It offers a wide spectrum of magnetic couplings on its side channel pumps, with optional ceramic separating cans to avoid eddy current losses.

Where a seal is acceptable, Circutec lists mechanical seals in carbon, SiC or FKM on its close-coupled pumps, with other materials on request, and single and double-acting mechanical seals on request on its side channel pumps, depending on the medium.

The US Department of Energy sourcebook says that on centrifugal pumps the packing or mechanical seals must be replaced periodically, but that this usually needs only a minor amount of downtime.

Ask for the explosion-protection marking of the exact model: Circutec lists ATEX II 2GD IIC cb TX on several of its ranges.

What the manufacturers say
Magnetic coupling
Circutec: leakage-free, low-maintenance and safe in operation
Mechanical seal
Circutec: carbon, SiC or FKM, other materials on request
Sealless vertical
Circutec: sealless and therefore maintenance-free, for open circuits
Peristaltic
Thomas: only the tubing comes into contact with the liquid
Check 8

Maintenance and spare parts.

Ask what wears, how often it is changed and how quickly, and who holds the spare parts and the technicians in Portugal.

The US Department of Energy sourcebook says centrifugal pumps typically suffer less wear and need fewer part replacements than displacement pumps, whose cyclical action can fatigue components such as bearings and diaphragms. For relief valves, it says a regular maintenance programme to check them should be strictly followed.

Thomas says the tubing or the pump head of a peristaltic pump can be replaced in a matter of seconds, and that its liquid diaphragm pumps with brushless DC motors can reach lifetimes of over 10,000 hours.

Ask for the datasheet and the parts list of the exact model before you order.

How Ultra Controlo supports it
Parts and training
Every Ultra Controlo partnership includes certification, technical training, a stock of genuine parts and UltraCare, our technical support programme
UltraCare, 24/7
Preventive and corrective maintenance, original spare parts and emergency support, 24 hours a day, 7 days a week
Our own technicians
Diagnosis, repair and maintenance on site by our own certified, factory-trained team, with scheduled maintenance plans for each installation
By technology at a glance

Six pump types, what each one suits.

A summary of what the manufacturers say. The series we supply in Portugal for each technology are on the industrial pumps page.

TechnologyWhat it suitsWhat to check
Multistage centrifugalHigh flow rates, with higher delivery pressures from multi-stage designs, says Circutec; SPECK (Neunkirchen) names pressure boosting, water treatment, irrigation and fire systems for its vertical IN-VB and IN-VC.Normal-priming, so no gas shares; check the NPSH, the best efficiency point and the stainless steel or cast iron version.
Side channelSelf-priming delivery of liquids that carry gas, and filling and draining under difficult physical conditions, says Circutec.Clean to lightly contaminated liquids without abrasive solids; PN 40; the ASK adds an NPSH inducer stage for a low suction head.
Regenerative turbine (peripheral)High pressure at relatively low flow, pulsation-free, and able to deliver a share of gas, says Circutec.Clear or cloudy liquids without abrasive solids, up to 100 mm²/s; magnetic coupling versions are leakage-free.
High-pressure plungerVery high pressure at low flow, from 1.2 l/min to 500 l/min and up to 1,200 bar, says Speck Triplex.Clean water and non-aggressive media unless the model is built for others; the unloader or relief valve; pulsating flow.
PeristalticDosing and transfer where only the tubing may touch the liquid; self-priming and able to run dry, says Thomas.The tubing material and its life; flow follows motor speed; pulsation is high with only two or three rollers.
DiaphragmSmall flows of liquid or gas in an oil-less pump that can run dry, says Thomas.Check the flow and the pressure: the liquid diaphragm pumps give 180 to 1,800 ml/min and up to 4 bar.
Before you order

What to ask any supplier.

The duty point, in writing

Ask for the flow and the head at the duty point, the power the pump draws there, and where that point sits on the pump curve.

The NPSH

Ask for the NPSH the pump requires at that flow, and tell the supplier the NPSH your system provides.

The liquid, written down

Send the liquid, its temperature and viscosity, and any gas, solids or abrasives it carries.

Materials and seals, by code

Ask for the wetted materials, the seal type and the elastomer of the exact model.

The safeguards

For a displacement or plunger pump, ask which relief valve or unloader goes with it.

Parts and datasheet

Ask who services the pump, which spare parts are held in Portugal, and for the datasheet and manual of the exact model before you order.

How Ultra Controlo answers

Partner brands, one team in Portugal.

Ultra Controlo distributes and services industrial pumps in Portugal as partner brands: centrifugal, multistage, side channel, process, booster and drainage pumps from Speck Pumpen (Circutec and SPECK Neunkirchen), high-pressure plunger pumps from Speck Triplex, and diaphragm, peristaltic, piston and linear pumps from Thomas. The equipment is made by each manufacturer.

Speck Pumpen means two companies: Speck Pumpen Walter Speck, whose brand has been Circutec since June 2025, for side channel, peripheral, process, heat transfer and displacement pumps; and SPECK Pumpen Verkaufsgesellschaft, in Neunkirchen am Sand, for multistage, booster, fire water, drainage and plastic pumps. Ultra Controlo distributes and services pumps from both.

The industrial pumps page lists, for each technology, the series we supply from each brand, and the brand pages say what each manufacturer states about them. Tell us the liquid, the flow and the head, the pressure and the site, or the pump you want to replace.

Looking for vacuum rather than liquid? Read how to choose an industrial vacuum pump.

Frequently asked questions

Common questions about choosing a pump.

Questions buyers ask us about industrial pumps. More on the medical gas answers page.

How do I choose an industrial pump?

To choose an industrial pump, start from the liquid and its temperature, then check the flow and head, the NPSH and the risk of cavitation, any gas in the liquid, the pressure, the materials, the shaft seal or magnetic drive, and the maintenance and spare parts.

Send the supplier the liquid, the flow, the head and the site.

What is NPSH and why does it matter when choosing a pump?

The US Department of Energy sourcebook (2006) says a centrifugal pump must have a certain pressure at its inlet to avoid cavitation, called the net positive suction head (NPSH). NPSHA is what the system provides and NPSHR is what the pump requires, and a common design rule is to keep NPSHA 25% above NPSHR at all expected flow rates.

Which pump can handle gas in the liquid?

Speck Pumpen (Circutec) says its side channel pumps and its displacement pumps are suitable for the delivery of gas shares and are self-priming, while its centrifugal pumps are normal-priming and not suitable for gas shares.

Which pump gives high pressure at a low flow?

The US Department of Energy sourcebook (2006) says displacement pumps are typically more appropriate when the system requires high pressure at low flow, and that they need safeguards such as relief valves. Speck Triplex gives its NP series plunger pumps from 1.2 l/min at 170 bar to 134 l/min at 100 bar.

Do magnetic drive pumps leak?

Speck Pumpen (Circutec) describes its magnetic coupling pumps as leakage-free, low-maintenance and safe in operation. Check the exact model: it also offers its side channel pumps with single and double-acting mechanical seals on request, depending on the medium.

Are Circutec and SPECK Neunkirchen the same company?

No. Circutec is the brand that Speck Pumpen Walter Speck GmbH & Co KG introduced on 10 June 2025, per its announcement; SPECK Pumpen Verkaufsgesellschaft GmbH, in Neunkirchen am Sand, is a different company, per its imprint. Ultra Controlo distributes and services pumps from both.

Does Ultra Controlo make these pumps?

No. The Industrial 2026 catalogue lists them as partner brands that Ultra Controlo distributes and services; the equipment is made by each manufacturer.

Does Ultra Controlo service industrial pumps in Portugal?

Yes. Ultra Controlo distributes and services Speck Pumpen, Speck Triplex and Thomas pumps, and its UltraCare programme covers Ultra Controlo equipment and partner brands.

Request a project assessment

Ready to discuss an industrial pump?

Send us the liquid, the flow and the head, the pressure and the site, or the pump you want to replace. Our industrial team replies with the model that fits.

ISO 9001:2015
ISO 14001
80+ countries
40 years